OEM/ODM Factory Ph Transmitter Liquisys Cpm253-Mr0005 - Online PH transmitter with sensor – JIRS Detail:
Code: BSQ-PH-2019
General introduction
EC/ER/pH/ORP-2019 series transmitter mainly used for the water quality monitor sensor signal output, by 4-20mA, RS485 or TTL, the sensor output weak signal is enlarged to transmit, can be convenient for PLC, configuration software and SCM to communicate by adopting standard communication protocol MODBUS protocol.
EC/ER/pH/ORP series transmitter is widely used in metallurgy manufacturing, power, light industry, textile, water treatment equipment, water pipe network and the scientific research and other industrial sectors.
Transmitter series introduction
Note: A module of the transmitter can only be equipped with one
sensor, EC/ER is a module, and PH / ORP is a module.
①: EC conductivity transmitter; range: 0 ~ 4000us / cm, 0-10/20/200mS
②: ER resistivity transmitter; range: 0 ~ 18.2MΩ
③: pH transmitter; range: 0 ~ 14.00 pH
④: ORP redox potential transmitter; range: -2000 ~ + 2000mV
Transmitter series technique specification
|
No. |
Range |
Matched sensor |
Accuracy |
Connection |
|
1 |
0.1～18.25MΩ 0.05～10.00uS） |
1：316L S.S. plug into 0.01 sensor 2：Quick install 0.02 sensor； |
2 %FS |
1/2″NPT 1/4”Quick install |
|
2 |
0.1～200.0uS |
316L S.S. plug-into 0.1 sensor |
|
1/2″NPT） |
|
3 |
0.5～2000uS（standard） |
ABS1.0 Pt. Black sensor(standard) 316L S.S. plug into 1.0 sensor |
1.5% FS |
1/2″NPT
|
|
4 |
2～4000uS |
ABS1.0 Pt. Black sensor(standard) 316L S.S. plug into 1.0 sensor |
1.5% FS |
1/2″NPT
|
|
5 |
0.5～10mS |
ABS1.0 Pt. Black sensor(standard) 316L S.S. plug into 1.0 sensor |
3 % FS |
1/2″NPT
|
|
6 |
0.5～20mS |
1：316LS.S. plug into10.0 (standard) 2：PTFE+Titanium alloy 10.0 sensor |
1.5 % FS |
1/2″NPT 3/4″NPT |
|
7 |
0.5～100mS |
1：316LS.S. plug into10.0 (standard) 2：PTFE+Titanium alloy 10.0 sensor |
2 % FS |
1/2″NPT 3/4″NPT |
|
8 |
0.5～200mS |
PTFE+Titanium alloy 10.0 sensor |
2 % FS |
3/4″NPT |
PH transmitter technique specification
Measuring range: 0～14.00,
Accuracy:2.0%(FS),
Stability: ±2×10-3FS/24h,
Sensor: online PH sensor,
Sensor threaded size: 3/4″ BSP,
Cable length: standard length is 5m,
Measured media temperature:0～50℃,
Temperature sensor: NTC 10K,
Temperature compensation: On basis of 25℃, AUTO or Manual temperature compensation,
Calibration mode: Three points calibration,
PH4.00,PH6.86,PH9.18,
Other common technique specification
Output current: 4～20mA, isolated / Optional:1-5V /2-10V;
Relay output: High/Low limit relay alarm output, Contact point current 24V/3A, 220V/2A ( Passive dry contact)
Power: DC12V-28V, 24V(Current <=0.1A),
Environmental conditions: Working temperature:0～50℃, Relative humidity: ≤ 85%RH,
Overall dimension: 122×72×45mm(L x W x H),
Installation mode: Cabinet rail installation
Product detail pictures:
Related Product Guide:
We've been proud with the significant shopper fulfillment and wide acceptance due to our persistent pursuit of top of the range both of those on solution and repair for OEM/ODM Factory Ph Transmitter Liquisys Cpm253-Mr0005 - Online PH transmitter with sensor – JIRS , The product will supply to all over the world, such as: Angola, Sudan, Belgium, We can meet the various needs of customers at home and abroad. We welcome new and old customers to come to consult & negotiate with us. Your satisfaction is our motivation! Allow us to work together to write a brilliant new chapter!
By ROGER Rivkin from Sao Paulo - 2018.12.11 11:26
Products and services are very good, our leader is very satisfied with this procurement, it is better than we expected,
By Constance from Gabon - 2018.11.04 10:32
